INPUT:
75ohm BNC, internally terminated

INPUT RETURN LOSS:
=18 dB to 270 MHz

INPUT LEVEL:
800 mV p-p ±10%

INPUT CABLE EQUALIZATION:
Automatic equalization for a minimum of
200m of 8281

OUTPUT CONNECTORS:
8 BNC

OUTPUT FORMAT COMPATIBILITY:
4 component serial digital
(270 Mb/s, 525/625 line)
4 composite analog
(NTSC/PAL, input dependent)

OUTPUT IMPEDANCE:
75ohm, source terminated

ANALOG OUTPUTS
DIFFERENTIAL GAIN: =1.5%

DIFFERENTIAL PHASE: =1.5°

FREQUENCY RESPONSE:
±0.25 dB to 4.5 MHz

OUTPUT LEVEL:
1V p-p ±1%, internally adjustable

SC/H PHASE: 0°±10°

RETURN LOSS: =40 dB

CHROMA-LUMA DELAY: <10 ns

DC OFFSET: 0V ±100 mV

DIGITAL OUTPUTS
DC OFFSET: 0V ±0.5V

RISE AND FALL TIME:
0.4 - 1.5 ns nominal measured from
20% to 80% points

THROUGHPUT DELAY:
15 ns nominal

OUTPUT LEVEL:
800 mV p-p ±10%

RETURN LOSS: =15 dB

STANDARDS AVAILABLE:
525 and 625

SPECIFICATIONS:

VIDEO
FORMAT COMPATIBILITY:
SMPTE 259M, ITU-R BT.601/656
Serial Component
(270 Mb/s, 525/625 line)

INPUT:
75ohm BNC, looping

INPUT RETURN LOSS:
>18 dB to 270 MHz

INPUT LEVEL:
800 mV p-p ±10%

INPUT CABLE EQUALIZATION:
Automatic equalization for up to
300m of 8281

OUTPUTS:
2 composite analog
(NTSC/PAL, input dependent)

OUTPUT IMPEDANCE:
75ohm, source terminated

OUTPUT LEVEL:
1V p-p nominal

FREQUENCY RESPONSE:
±1 dB to 5 MHz

DIFFERENTIAL GAIN:
=2.0%

DIFFERENTIAL PHASE:
=1.5°

STANDARDS AVAILABLE:
525 and 625 Supports NTSC and NTSC-J

OUTPUTS: 8

CONNECTORS: BNC

INPUT RETURN LOSS:
>40 dB to 5 MHz

MAXIMUM INPUT LEVEL:
2V p-p

OUTPUT IMPEDANCE:
75ohm, source terminated

MAXIMUM OUTPUT LEVEL:
2V p-p, 75? load

GAIN:
Continuously adjustable from
–3 dB to +3 dB

FREQUENCY RESPONSE:
±0.25 dB to 5 MHz
+0.25 dB, –2 dB to 10 MHz

DIFFERENTIAL GAIN: <0.1%

DIFFERENTIAL PHASE: <0.1°

TILT: <1% maximum

OVERSHOOT AND RINGING:
<1% maximum

OUTPUT ISOLATION:
>40 dB to 5 MHz at full load

DC OFFSET:
0V ±100 mV

THROUGHPUT DELAY:
12 ns typical

STANDARDS AVAILABLE:
NTSC and PAL

OUTPUTS:
4 stereo outputs, balanced or unbalanced

CONNECTORS:
2 detachable connectors

INPUT IMPEDANCE:
Hi-Z

MAXIMUM INPUT LEVEL:
+24 dBm balanced

CMRR:
>80 dB @ 60 Hz,
>75 dB @ 20 kHz

OUTPUT IMPEDANCE:
<50ohm

MAXIMUM OUTPUT LEVEL:
+24 dBm balanced

GAIN:
–6 dB to +33 dB

NOISE:
>85 dB, 20 Hz to 20 kHz

FREQUENCY RESPONSE:
±0.05 dB, 20 Hz to 20 kHz
±0.25 dB, 10 Hz to 50 kHz

THD:
<0.01%

INTERMOD DISTORTION:
<0.02%

INTERCHANNEL CROSSTALK:
>90 dB

ISOLATION BETWEEN MODULES:
>100 dB

CHANNEL PHASE MATCHING:
<100 ns

AMPLITUDE: 47.5 IRE ±1 IRE

DC OFFSET: 0V ±100 mV

RESIDUAL SUBCARRIER:
=1 IRE AUDIO One balanced output via detachable connector

FREQUENCY:
1 kHz, ±5%, sine wave

LEVEL:
+4 dBm, ±0.5 dB (internally adjustable)

IMPEDANCE: 600ohm

THD: =1%

SWITCHABLE OUTPUT
Four times subcarrier digitally generated
RS-170M SMPTE bar with pluge and
I and Q bars.

BAR ACCURACY: within 1°

AMPLITUDE: =1%

DC OFFSET: 0V ±50mV

LUMINANCE:
100% white bar, 100 IRE ±1 IRE

RESIDUAL SUBCARRIER: =1 IRE
OVER/UNDERSHOOT AND RINGING:
<1% at 1V p-p output

FCC MULTIBURST
REFERENCE BAR AMPLITUDE:
100 IRE

REFERENCE PACKET AMPLITUDE:
60 IRE

BURST FREQUENCIES:
0.5, 1.25, 2.0, 3.0, 3.58 and 4.1 MHz

10-STEP MODULATED STAIRSTEP
CHROMINANCE AMPLITUDE: 40 IRE

10-STEP STAIRSTEP
Ten equal amplitude steps from 7.5 to
100.0 IRE

STANDARDS AVAILABLE:
NTSC and NTSC-J

HIGH SPECIFICATIONS: Minimal degradation of distributed signals.

RELIABLE: Self-contained power supplies. No single point of failure
as with common power supply frames.

SPECIFICATIONS:

POWER
INPUT:
90-132, 180-264 VAC,
50/60 Hz

CONNECTOR:
Per IEC-320

CORD:
3-wire detachable

MECHANICAL
DIMENSIONS:
Height: 5.25”(13.4 cm)
Width: 19”(48.3 cm)
Depth: 12.1”(30.8 cm)
WEIGHT:
11.8 lb (5.4 kg) (without modules)

STANDARD ACCESSORIES
Operation & Service Manual, power cord

OPTIONS
XC-OF:
Extender Cable for servicing
OMNIFRAME modules.

RB-OF:
Back Support Kit which provides additional
frame support by attaching to back rack
rails. Recommended for ENG & SNG
vehicles.